Wolverine By Prince Manufacturing means

  • Globally sourced for great prices!!!
  • Products developed and tested in our unique R&D lab!!!
  • Manufactured to our specifications!!!
  • More products added regularly so check back often!!!

image description

3000 PSI Rated with Cross Tube

  • 1.5" – 4” Bores
  • 4" – 48” Strokes
  • 100% tested
  • Cast steel end fittings
  • Hard chrome rod plating
  • SAE O-ring ports
  • Thread-in gland
  • Grease zerks included
image description

3000 PSI Rated with Clevis

  • 1.5" – 4” Bore Sizes
  • 4" – 48” Strokes
  • 100% tested
  • Cast steel end fittings
  • Hard chrome rod plating
  • SAE O-ring ports
  • Thread-in gland
  • Pins and clips Included
image description

Tie-Rod Cylinders

  • 2" - 4" Bore Sizes
  • 4" - 36" Strokes
  • 100% tested
  • Forged Clevises
  • Individually bagged and boxed
image description

Wolverine MB – 8GPM

  • 1-6 Spool monoblock
  • 3500 psi
  • #8 O-ring In/Out ports
  • #8 Work ports
  • Interchangable motor spool
  • Double acting
  • Load check
  • Open center
  • Adjustable relief
  • Enclosed handle
  • Convertible to power beyond and closed center capability
image description

3000 PSI Rated with Swivel Ball Ends

  • 1" – 3” Bores
  • 4" – 30” Strokes
  • 100% tested
  • Cast steel end fittings
  • Hard chrome rod plating
  • North American source seals
  • SAE O-ring ports
  • Thread-in gland
image description

Hydraulic Handpump

  • Up to 3500 psi working pressure
  • "SA" Series is Single Acting
  • "DA" Series have a built in Directional Control Valve
  • 1.5 and 2.1 Cubic Inch Per Cycle (One Up and One Down)
image description

Log Splitter

  • Pressure release detent at end of retract stroke
  • Relief set at 2,250 psi
  • Max tank port pressure 500 psi
  • Max operating temperature 180° F
image description

Flow Control Valve

  • Standard 3-port allows for pressure compensated flow out of two ports.
  • Optional 2-port allows for pressure compensated flow out of one port.
  • Models available with adjustable ball spring relief.
  • Standard relief setting is 1500 psi.
  • Side Port Configuration
  • External seals on side lever spool prevents contamination from locking up spool
  • Rated for 3000 psi
  • 100% Tested
  • Weight is 8 lbs.
  • Cross-over for many popular models in the market
image description

Ball Valve

  • 1/4", 3/8", 1/2" sizes 7,250 psi (CWP)
  • 3/4", 1” sizes 4,500 psi (CWP)
  • Carbon Steel Body Zinc Plated
  • Hard Chrome Plated Steel Ball, POM Seat
  • 3 way valves are “L” Type
  • Operating Temp -20° to 175° F
  • Not Recommended for Steam, Gas, or Water Service
image description

In-Line Needle Valve

  • Carbon Steel Body
  • Designed to provide precision flow control
  • Operating temperature -20°F through 210°F
image description

Inline Flow Control

  • Carbon Steel Body
  • Designed to provide precision flow control & shut off in one flow direction & provide free flow in the opposite direction
  • Color bands allow fast return to a previous setting
  • Set screw locks valve to any setting
image description

Hydraulic Motors

  • High-torque, low speed with gerotor
  • Instantly reversible (by reversing flow)
  • Cross-over for many popular models in the market
image description

Gear Pumps

  • Reversible gear sets
  • Cast iron front & back covers
  • Viton seals available
  • Working pressures up to 3600 PSI
  • Customization available
    • Flanges
    • Shaft sizes
    • Flow control rear cover
  • Double pumps: Available in WPA, WPB & WPC
  • Maximum speed from 2500 to 4000 RPM using SAE 10W oil
  • Displacement covers 0.27 in3/rev. to 4.48 in3/rev.
  • Inlet pressure: Pump inlet should not exceed 5 in. of mercury vacuum or 14 PSI positive pressure
  • Ports: SAE straight thread O-ring boss for WPA, WPB & WPC
  • Working oil: A mineral based oil with additives to resist corrosion oxidation, & foaming is recommended. Viscosity at any running condition should be 60 SUS minimum & 250 SUS maximum. 180° F is the maximum recommended system operating temperature
  • Filtration: Per ISO cleanliness code level 17/14/15 micron filtration for full PSI is recommended
image description

PTO Pumps

  • Cast iron end plates with aluminum center section
  • Self-Adjusting wear plates
  • Tapped holes for torque arm kit to prevent pump rotation
  • Hose barb for inlet port and NPT adapter for outlet port
  • Slips onto tractor PTO shaft (no gear box required)